manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 194

INS_CWGE24MS2_REV–

10/05/16     PAGE 194

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

STP Status

Parameter

Description

Current Root Status
Instance

The Instance ID.

MAC address

This is the MAC address of the root bridge.

Priority

Root refers to the base of the spanning tree (the root bridge). This field displays the 
root bridge’s priority. This Switch may also be the root bridge.

Root Cost

This is the path cost to the root bridge.

MAX Age

This is the maximum time (in seconds) the Switch can wait without receiving a 
configuration message before attempting to reconfigure.

Hello Time

This is the time interval (in seconds) at which the root switch transmits a configuration 
message. The root bridge determines Hello Time, Max Age and Forwarding Delay.

Forward Delay

This is the time (in seconds) the root switch will wait before changing states.

Root Port

This is the port to the root bridge.

Current Bridge Status
Instance

This is the MAC address of the current bridge.

MAC address

This is the MAC address of the bridge.

Priority

This is the priority of the Switch.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды