Comnet CWGE24MS2 Скачать руководство пользователя страница 272

Страница: 272 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 272

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Upload / Download Configurations to/from your server

Follow the steps below to save the configuration file to your PC.

» Select the “Press “Download” to save configurations file to your PC”.

» Click the “Download” button to start the process.

Follow the steps below to load the configuration file from your PC to the Switch.

» Select the “Upload configurations file to your Switch”.

» Select the full path to your configuration file.

» Click the Upload button to start the process.

Reset the factory default settings of the Switch

Press the Reset button to set the settings to factory default configurations.

The configuration status

Display the configuration status of recorded in the NV-RAM.

Notice: If the user has changed any configurations, the message displays “The configurations

have been modified!” Otherwise, the message “The configurations are default values.”

There are two conditions will change message from “The configurations have been modified!” to
“The configurations are default values.”

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды