Comnet CWGE24MS2 Скачать руководство пользователя страница 109

Страница: 109 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 109

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configuration

Node

Command

Description

enable

show protocol-vlan

This command displays the all of the
protocol-vlan configurations.

configure protocol-vlan frame-type ethernetII ether-type

STRINGS vlan VLANID ports PORTLISTS

This command creates a protocol-vlan
entry with ethernetII frame type.

configure protocol-vlan frame-type nonLLC-SNAP vlan

VLANID ports PORTLISTS

This command creates a protocol-vlan
entry with nonLLC-SNAP frame type.

configure protocol-vlan frame-type LLC-SNAP vlan VLANID

ports PORTLISTS

This command creates a protocol-vlan
entry with LLC-SNAP frame type.

configure no protocol-vlan frame-type ethernetII ether-type

STRINGS vlan VLANID

This command deletes a protocol-vlan
entry with ethernetII frame type.

configure no protocol-vlan frame-type nonLLC-SNAP vlan

VLANID

This command deletes a protocol-vlan
entry with nonLLC-SNAP frame type and
vlan.

configure no protocol-vlan frame-type LLC-SNAP vlan VLANID This command deletes a protocol-vlan

entry with LLC-SNAP frame type and vlan.

configure no protocol-vlan all

This command deletes all of the protocol-
vlan entries.

Example:

CWGE24MS2(config)#protocol-vlan frame-type LLC-SNAP vlan 12 ports 1-2
CWGE24MS2(config)#protocol-vlan frame-type nonLLC-SNAP vlan 13 ports 3-4
CWGE24MS2(config)#protocol-vlan frame-type ethernetII ether-type 0800 vlan 14 ports 1-2

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды