Comnet CWGE24MS2 Скачать руководство пользователя страница 117

Страница: 117 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 117

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configuration

Node

Command

Description

enable

show vlan-stacking

This command displays the current vlan-stacking type.

enable

show vlan-stacking selective-
qinq

This command displays the selective Q-in-Q configurations.

enable

show vlan-stacking
portbased-qinq

This command displays the port-based q-in-Q configurations.

enable

show vlan-stacking tpid-
inform

This command displays the TPID configurations.

configure vlan-stacking (disable|port-

based|selective)

This command disable the vlan stacking or enable the vlan-
stacking with port-based or selective on the switch.

configure vlan-stacking selective-qinq

STRINGS

This command creates a selective Q-in-Q profile with the name.

configure no vlan-stacking selective-

qinq STRINGS

This command removes the selective Q-in-Q profile with the
name.

configure vlan-stacking tpid-table index

<2-6> value STRINGS

This command configures TPID table.

interface

vlan-stacking port-based
priority <0~7>

This command sets the priority in port based Q-in-Q.

interface

vlan-stacking port-based role
(tunnel|access|normal)

This command sets VLAN stacking port role.

interface

vlan-stacking port-based
spvid <1~4096>

This command sets the service provider’s VID of the specified
port.

interface

vlan-stacking tunnel-tpid
index <1-6>

This command sets TPID for a Q-in-Q tunnel port.

configure interface range

gigabitethernet1/0/ ORTLISTS

This command enters the interface configure node.

if-range

vlan-stacking port-based
priority <0~7>

This command sets the priority in port based Q-in-Q.

if-range

vlan-stacking port-based role
(tunnel|access|normal)

This command sets VLAN stacking port role.

if-range

vlan-stacking port-based
spvid <1~4096>

This command sets the service provider’s VID of the specified
port.

if-range

vlan-stacking tunnel-tpid
index <1-6>

This command sets TPID for a Q-in-Q tunnel port.

qinq

active

This command enables the selective Q-in-Q profile.

qinq

inactive

This command disables the selective Q-in-Q profile.

qinq

cvid VLANID

This command specifies the customer’s VLAN range on the
incoming packets.

qinq

spvid VLANID

This command sets the service provider’s VLAN ID for outgoing
packets in selective Q-in-Q.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды