manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 180

INS_CWGE24MS2_REV–

10/05/16     PAGE 180

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Web Configuration

General Settings

Parameter

Description

State

Select Enabled to use Spanning Tree Protocol (STP) or Rapid Spanning Tree Protocol (RSTP).

Mode

Select to use either Spanning Tree Protocol (STP) or Rapid Spanning Tree Protocol (RSTP).

Forward TimeThis is the maximum time (in seconds) the Switch will wait before changing states. This 

delay is required because every switch must receive information about topology changes 
before it starts to forward frames. In addition, each port needs time to listen for conflicting 
information that would make it return to a blocking state; otherwise, temporary data loops 
might result. The allowed range is 4 to 30 seconds.

Max Age

This is the maximum time (in seconds) the Switch can wait without receiving a BPDU before 
attempting to reconfigure. All Switch ports (except for designated ports) should receive 
BPDUs at regular intervals.
Any port that age out STP information (provided in the last BPDU) becomes the designated 
port for the attached LAN. If it is a root port, a new root port is selected from among the 
Switch ports attached to the network. The allowed range is 6 to 40 seconds.

Hello Time

This is the time interval in seconds between BPDU (Bridge Protocol Data Units) configuration 
message generations by the root switch. The allowed range is 1 to 10 seconds.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды