Comnet CWGE24MS2 Скачать руководство пользователя страница 156

Страница: 156 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 156

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configuration

Node

Command

Description

enable

show loop-detection

This command displays the current loop detection configurations.

configure loop-detection (disable |

enable)

This command disables / enables the loop detection on the switch.

configure

loop-detection address
MACADDR

This command configures the destination MAC for the loop
detection special packets.

configure

no loop-detection
address

This command configures the destination MAC to default
(00:0b:04:AA:AA:AB).

interface

loop-detection (disable |
enable)

This command disables / enables the loop detection on the port.

interface

no shutdown

This command enables the port. It can unblock port blocked by
loop detection.

interface

loop-detection recovery
(disable | enable)

This command enables / disables the recovery function on the port.

interface

loop-detection recovery
time VALUE

This command configures the recovery period time.

configure

interface range
gigabitethernet1/0/
PORTLISTS

This command enters the interface configure node.

if-range

loop-detection (disable |
enable)

This command disables / enables the loop detection on the ports.

if-range

loop-detection recovery
(disable | enable)

This command enables / disables the recovery function on the port.

if-range

loop-detection recovery
time VALUE

This command configures the recovery period time.

Example:

CWGE24MS2(config)#loop-detection enable

CWGE24MS2(config)#interface 1/0/1

CWGE24MS2(config-if)#loop-detection enable

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды