Comnet CWGE24MS2 Скачать руководство пользователя страница 251

Страница: 251 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 251

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Web Configuration

Parameter

Description

State

Globally enables / disables the traffic monitor function.

Port

The port range which you want to configure.

State

Enables / disables the traffic monitor function on these ports.

Action

Unblock these ports.

Packet Type

Specify the packet type which you want to monitor.

Packet Rate

Specify the packet rate which you want to monitor.

Recover State

Enables / disables the recovery function for the traffic monitor function on
these ports.

Recovery Time Configures the recovery time for the traffic monitor function on these

ports.(Range: 1 – 60 minutes)

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды