manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 48

INS_CWGE24MS2_REV–

10/05/16     PAGE 48

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

For Auto-MDIX to operate correctly, the speed on the interface and duplex setting must be set 
to “auto”. Auto-MDIX was developed by HP engineers Dan Dove and Bruce Melvin.

 

» Auto Negotiation 
Auto (auto-negotiation) allows one port to negotiate with a peer port automatically to obtain the 
connection speed and duplex mode that both ends support. When auto-negotiation is turned 
on, a port on the Switch negotiates with the peer automatically to determine the connection 
speed and duplex mode. 
If the peer port does not support auto-negotiation or turns off this feature, the Switch 
determines the connection speed by detecting the signal on the cable and using half duplex 
mode. When the Switch’s auto-negotiation is turned off, a port uses the pre-configured speed 
and duplex mode when making a connection, thus requiring you to make sure that the settings 
of the peer port are the same in order to connect.

 

» Flow Control 
A concentration of traffic on a port decreases port bandwidth and overflows buffer memory 
causing packet discards and frame losses.IEEE802.3x flow control is used in full duplex mode to 
send a pause signal to the sending port, causing it to temporarily stop sending signals when the 
receiving port memory buffers fill and resend later. 
The Switch uses IEEE802.3x flow control in full duplex mode and backpressure flow control in 
half duplex mode. IEEE802.3x flow control is used in full duplex mode to send a pause signal to 
the sending port, causing it to temporarily stop sending signals when the receiving port memory 
buffers fill. Back Pressure flow control is typically used in half duplex mode to send a “collision” 
signal to the sending port (mimicking a state of packet collision) causing the sending port to 
temporarily stop sending signals and resend later.

Note: 1000 Base-T doesn’t support force mode.

Default Settings

The default port Speed & Duplex is auto for all ports.

The default port Flow Control is Off for all ports.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды