manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 29

INS_CWGE24MS2_REV–

10/05/16     PAGE 29

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Jumbo Frame

Introduction

Jumbo frames are Ethernet frames with a payload greater than 1500 bytes. Jumbo frames can 
enhance data transmission efficiency in a network. The bigger the frame size, the better the 
performance.

Notice:

The jumbo frame settings will apply to all ports.

If the size of a packet exceeds the jumbo frame size, the packet will be dropped.

The available values are 1522, 1536, 1552, 9010, 9216, 10240.

Default Settings

The default jumbo frame is 10240 bytes.

CLI Configuration

Node

Command

Description

enable

show jumboframe

This command displays the current jumbo frame settings.

configure

jumboframe (10240|1522|1536|
1552|9010|9216)

This command configures the maximum number of bytes of 
frame size for all ports.

configure

interface IFNAME

This command enters the interface configure node.

interface

jumboframe (10240|1522|1536|
1552|9010|9216)

This command configures the maximum number of bytes of 
frame size.

configure

interface range 
gigabitethernet1/0/ 
PORTLISTS

This command enters the interface configure node.

if-range

jumboframe (10240|1522|1536|
1552|9010|9216)

This command configures the maximum number of bytes of 
frame size.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды