Comnet CWGE24MS2 Скачать руководство пользователя страница 250

Страница: 250 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 250

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configuration

Node

Command

Description

enable

show traffic-monitor

This command displays the traffic monitor configurations and
current status.

configure

traffic-monitor
(disable|enable)

This command enables / disables the traffic monitor on the
Switch.

interface

traffic-monitor
(disable|enable)

This command enables / disables the traffic monitor on the port.

interface

traffic-monitor rate
RATE_LIMIT type
(bcast|mcast|bcast+mcast)

This command configures the packet rate and packet type for the
traffic monitor on the port.
bcast – Broadcast packet.
mcast – Multicast packet.

interface

traffic-monitor recovery
(disable|enable)

This command enables / disables the recovery function for the
traffic monitor on the port.

interface

traffic-monitor recovery time
VALUE

This command configures the recovery time for the traffic
monitor on the port.

configure

interface range
gigabitethernet1/0/
PORTLISTS

This command enters the interface configure node.

if-range

traffic-monitor
(disable|enable)

This command enables / disables the traffic monitor on the port.

if-range

traffic-monitor rate
RATE_LIMIT type
(bcast|mcast|bcast+mcast)

This command configures the packet rate and packet type for the
traffic monitor on the port.
bcast – Broadcast packet.
mcast – Multicast packet.

if-range

traffic-monitor recovery
(disable|enable)

This command enables / disables the recovery function for the
traffic monitor on the port.

if-range

traffic-monitor recovery time
VALUE

This command configures the recovery time for the traffic
monitor on the port.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды