Comnet CWGE24MS2 Скачать руководство пользователя страница 167

Страница: 167 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 167

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Parameter

Description

Port Number

Selects a port number you want to configure on this screen

State

Selects Enable to activate the port or Disable to deactivate the port

Trusted

Selects yes to sets a physical interface as trusted port

Vendor-Tag

Set the retransmitting policy of the specific interface for the PADO/PADS
packet<keep|replace|strip>. Default:Keep

Circuit-ID String

User defined circuit ID string on specific interface for the PPPoE IA

Remote ID String User defined remote ID string on specific interface for the PPPoE IA
Interface VLAN

Selects Add to increase the interface Vlan or Remove to delete the interface Vlan

Circuit-ID String

User defined circuit ID string on specific interface vlan for the PPPoE IA

Remote-ID String User defined remote ID string on specific interface vlan for the PPPoE IA
Apply

Click Apply to take effect the settings.

Refresh

Click Refresh to begin configuring this screen afresh.

Port

Selects a port number you want to display its configurations.

Show

Show the configurations of the port.

Statistics

Parameter

Description

VLAN

Displays the current statistics of the vlan for the PPPoE IA.

PPPoE discovery packet

PPPoE packet type

Received

Total received packet

Forwarded

Total forwarded packet

Dropped

Total dropped packet

Show

Show the statistics of the vlan.

clear

Clear the statistics of the vlan.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды