manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 169

INS_CWGE24MS2_REV–

10/05/16     PAGE 169

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Node

Command

Description

configure no ipv4 arp  <IPv4_

ADDR> <MAC_ADDR>

This command deletes a static IPv4 ARP entry from ARP table.

configure no ipv6 arp  <IPv6_

ADDR> <MAC_ADDR>

This command deletes a static IPv6 ARP entry from ARP table.

configure interface vlan VLAN-ID This command enters the L3 interface node.
L3 
interface

ipv4 address 
A.B.C.D/M

This command assigns a specified IPv4 interface route to the interface.
We can assign multiple IPv4 interface route to a single interface with 
different IP segment.
If this configuration is a first IP assigning to the interface then 
automatically interface is enabled for routing.

L3 
interface

ipv6 address <IPv6_
ADDR>/M

This command assigns a specified IPv6 interface route to the interface.
We can assign only one IPv6 interface route for an interface vlan.
If this configuration is a first IP assigning to the interface then it 
automatically enables the interface with routing.

L3 
interface

no ipv4 address 
A.B.C.D/M

This command deletes a specified IPv4 interface route from the 
interface vlan.
This command deletes all dependent static routes on the specified IPv4 
interface route.
If there is no assigned IP addresses for the specified interface after 
deleting then it will automatically disables routing in interface. 

L3 
interface

no ipv4 address <IPv6_
ADDR>/M

This command deletes a specified IPv6 interface route from the 
interface.
This command deletes all dependent static routes on the specified IPv6 
interface route.
If there is no assigned IP addresses for the specified interface after 
deleting then it will automatically disables routing in interface vlan.

L3 
interface

ipv4 route A.B.C.D/M 
A.B.C.D

This command configures an IPv4 static route onto the specified 
interface vlan.

L3 
interface

ipv6 route <IPv6_
ADDR>/M <IPv6_
ADDR>

This command configures an IPv6 static route onto the specified 
interface vlan.

L3 
interface

no ipv4 route 
A.B.C.D/M A.B.C.D

This command deletes a specified IPv4 static route from an interface 
vlan.

L3 
interface

no ipv6 route <IPv6_
ADDR>/M <IPv6_
ADDR>

This command deletes a specified IPv6 static route from an interface 
vlan.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды