Comnet CWGE24MS2 Скачать руководство пользователя страница 177

Страница: 177 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 177

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Default Settings

STP/RSTP

disabled.

STP/RSTP mode

: RSTP.

Forward Time

: 15 seconds.

Hello Time

: 2 seconds.

Maximum Age

: 20 seconds.

System Priority

: 32768.

Transmission Limit

: 3 seconds.

Per port STP state

: enabled.

Per port Priority

: 128.

Per port Edge port

: disabled.

Per port BPDU filter

: disabled.

Per port BPDU guard

: disabled.

Per port BPDU Root guard

: disabled.

Per port Path Cost

: depend on port link speed.

Example: Bandwidth -> STP Port Cost Value
10 Mbps ->

100

100 Mbps ->

1 Gbps

10 Gbps

CLI Configuration

Node

Command

Description

enable

show spanning-tree
active

This command displays the spanning tree information for only active
port(s)

enable

show spanning-tree
blockedports

This command displays the spanning tree information for only blocked
port(s)

enable

show spanning-tree
port detail PORT_ID

This command displays the spanning tree information for the interface
port.

enable

show spanning-tree
statistics PORT_ID

This command displays the spanning tree information for the interface
port.

enable

show spanning-tree
summary

This command displays the summary of port states and configurations

enable

clear spanning-tree
counters

This command clears spanning-tree statistics for all ports.

enable

clear spanning-tree
counters PORT_ID

This command clears spanning-tree statistics for a specific port.

configure spanning-tree (disable |

enable)

This command disables / enables the spanning tree function for the
system.

configure spanning-tree

algorithm-timer
forward-time TIME
max-age TIME hello-
time TIME

This command configures the bridge times (forward-delay,max-
age,hello-time).

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды