manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 15

INS_CWGE24MS2_REV–

10/05/16     PAGE 15

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

The RJ-45 Ethernet port fully supports auto-sensing and auto-negotiation. 

 

»  Insert one end of a Category 3/4/5/5e (see recommendation above) type twisted-pair cable 

into an available RJ-45 port on the Switch and the other end into the port of the network node. 

 

»  Check the corresponding port LED on the Switch to ensure that the connection is valid. (Refer 

to LED chart)

Connecting to the Console

The console port (DB-9) provides the out-of-band management facility. Use null modem cable to 
connect the console port on the Switch and the other end into the COM port of the computer. 

Connecting to Computer or a LAN

You can use Ethernet cable to connect computers directly to the switch ports. You can also 
connect hubs/switches to the switch ports by Ethernet cables. You can use either the crossover or 
straight-through Ethernet cable to connect computers, hubs, or switches. 

Notice: Use a twisted-pair Cat5e Ethernet cable to connect the 1000BASE-T port otherwise the 

link speed will not be able to reach 1Gbps.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды