manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 172

INS_CWGE24MS2_REV–

10/05/16     PAGE 172

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Parameter

Description

IPv4

Adds an IPv4 Interface Route / Static Route onto the interface vlan. / Deletes an IPv4 
Interface Route / Static Route from the interface vlan.
Selects the route type, Interface Route or Static Route.

IP/M:

The IP address and the netmask for the entry.

IP:

The static route address for the Static Route type only.

IPv6

Adds an IPv6 Interface Route / Static Route onto the interface vlan. / Deletes an IPv6 
Interface Route / Static Route from the interface vlan.
Selects the route type, Interface Route or Static Route.

IP/M:

The IP address and the netmask for the entry.

IP:

The static route address for the Static Route type only.

Status

Shows the ARP table / Host table / Route configurations.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды