Comnet CWGE24MS2 Скачать руководство пользователя страница 187

Страница: 187 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 187

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

CLI Configurations

Node

Command

Description

enable

show spanning-tree
mst configuration

This command displays the MSTP configurations.

enable

show spanning-tree
mst instance

This command displays all of the instance configurations of the MSTP.

enable

show spanning-tree
mst instance <0-63>

This command displays specific instance configurations of the MSTP.

enable

show spanning-tree
mst instance <0-63>
interface IFNAME

This command displays specific instance configurations on an interface
of the MSTP.

enable

show spanning-tree
mst interface IFNAME

This command displays the configurations on an interface of the MSTP.

enable

show spanning-tree
mst root

This command displays the root bridge configurations.

configure spanning-tree

(disable|enable)

This command enables / disables the spanning tree.

configure spanning-tree mode

mst

This command configures the mode of the spanning tree. (one of the
three modes STP/RSTP/MSTP.)

configure spanning-tree mst

forward-time

This command configures the forward time for the MSTP.

configure no spanning-tree mst

forward-time

This command resets the forward time for the MSTP.
The default forward delay time is 15 seconds.

configure spanning-tree mst

hello-time

This command configures the hello time for the MSTP.

configure no spanning-tree mst

hello-time

This command resets the hello time for the MSTP.
The default hello time is 2 seconds.

configure spanning-tree mst

max-age

This command configures the maximum age time for the MSTP.

configure no spanning-tree mst

max-age

This command resets the maximum age time for the MSTP.
The default maximum age time is 20 seconds.

configure spanning-tree mst

max-hops

This command configures the maximum hop count.

configure no spanning-tree mst

max-hops

This command resets the maximum hop count.
The default maximum hop count is 20.

configure spanning-tree mst

instance STRING
priority <0-61440>

This command resets the maximum hop count.
The default maximum hop count is 20.

configure no spanning-tree

mst instance STRING
priority

This command resets the priority for the specific instance.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды