Comnet CWGE24MS2 Скачать руководство пользователя страница 19

Страница: 19 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 19

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

How to enter the CLI

Press [Enter] key to enter the login command prompt when below message is displayed on the
screen.

Please press Enter to activate this console

Input “

admin

” to enter the CLI mode when below message is displayed on the screen.

CWGE24MS2 login:

You can execute a few limited commands when CLI prompt is displayed as below.

CWGE24MS2>

If you want to execute more powerful commands, you must enter the privileged mode.

Input command “

enable

”

CWGE24MS2>enable

Input a valid username and password when below prompt are displayed.

user:admin

password:admin

CWGE24MS2#

CLI command concept

Node

Command

Description

enable

show hostname

This command displays the system’s network name.

configure

reboot

This command reboots the system.

eth0

ip address A.B.C.D/M This command configures a static IP and subnet

mask for the system.

interface

show

This command displays the current port
configurations.

acl

show

This command displays the current access control
profile.

vlan

show

This command displays the current VLAN
configurations.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды