Comnet CWGE24MS2 Скачать руководство пользователя страница 85

Страница: 85 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 85

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Default Settings

There is no MVR vlan.

Default configuration for a new MVR:

MVR VLAN Information

VLAN ID

: 2

Name

: MVR2

Active

: Enabled

Mode

: Dynamic

Source Port(s)

: None

Receiver Port(s)

: None

Tagged Port(s)

: None

The Switch allows user to create up to 250 groups.

The Switch allows user to create up to 16 MVRs.

Notices

» IGMP snooping and MVR can be independently enabled.

» IGMP snooping and MVR use the same IGMP timers.

» MVR can recognize IGMPv3 reports.

» About the IGMPv3 report, switch doesn’t treat those group records with the following group

record types as membership reports. Those group record types are MODE_IS_INCLUDE,
CHANGE_TO_INCLUDE_MODE, ALLOW_NEW_SOURCES and BLOCK_OLD_SOURCES.

» Don’t use the group address X.0.0.1 for your multicast stream. It is because the system detects

and records the 224.0.0.1 for dynamic querier port. The group address X.0.0.1 may conflict with
224.0.0.1.

» Because the lower 23 bits of the 28-bit multicast IP address are mapped into the 23 bits of

available Ethernet address space. When you configure group address, the Switch compares
the lower 23 bits only.

» CLI command “group 1 start-address 224.1.1.1 6”, it creates 6 groups. That is, one IP, one group.

» The MVR name should be the combination of the digit or the alphabet.

» The group name should be the combination of the digit or the alphabet.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды