Comnet CWGE24MS2 Скачать руководство пользователя страница 178

Страница: 178 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 178

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Node

Command

Description

configure no spanning-tree

algorithm-timer

This command configures the default values for forward-time & max-
age & hello-time.

configure spanning-tree forward-

time <4-30>

This command configures the bridge forward delay time (sec).

configure no spanning-tree

forward-time

This command configures the default values for forward-time.

configure spanning-tree hello-

time <1-10>

This command configures the bridge hello time(sec).

configure no spanning-tree hello-

time

This command configures the default values for hello-time.

configure spanning-tree max-age

<6-40>

This command configures the bridge message max-age time(sec).

configure no spanning-tree max-

age

This command configures the default values for max-age time.

configure spanning-tree mode

(rstp|stp)

This command configures the spanning mode.

configure spanning-tree pathcost

method (short|long)

This command configures the pathcost method.

configure spanning-tree priority

<0-61440>

This command configures the priority for the system.

configure no spanning-tree

priority

This command configures the default values for the system priority.

interface

spanning-tree
(disable|enable)

This command configures enables/disables the STP function for the
specific port.

interface

spanning-
tree bpdufilter
(disable|enable)

This command configures enables/disables the bpdufilter function for
the specific port.

interface

spanning-tree
bpduguard
(disable|enable)

This command configures enables/disables the bpduguard function for
the specific port.

interface

spanning-
tree rootguard
(disable|enable)

This command enables/disables the BPDU Root guard port setting for
the specific port.

interface

spanning-tree edge-
port (disable|enable)

This command enables/disables the edge port setting for the specific
port.

interface

spanning-tree cost
VALUE

This command configures the cost for the specific port.
Cost range:
16-bit based value range 1-65535,
32-bit based value range 1-200000000.

interface

no spanning-tree cost This command configures the path cost to default for the specific port.

interface

spanning-tree port-
priority <0-240>

This command configures the port priority for the specific port.
Default: 128.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды