manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 220

INS_CWGE24MS2_REV–

10/05/16     PAGE 220

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Node

Command

Description

acl

action 802.1p 
remarking <0-7>

This command actives this profile and specify that it is for 802.1p 
remark. And configures the new 802.1p value which will be override to 
all packets matched this profile.

acl

802.1p VALUE

This command configures the 802.1p value for the profile.

acl

dscp VALUE

This command configures the DSCP value for the profile.

acl

destination mac host  
MACADDR

This command configures the destination MAC and mask for the 
profile.

acl

destination mac 
MACADDR  MACADDR

This command configures the destination MAC and mask for the 
profile.

acl

destination mac 
MACADDR  MACADDR

This command configures the destination MAC and mask for the 
profile. The second MACADDR parameter is the mask for the profile.

acl

no destination mac

This command removes the destination MAC from the profile.

acl

ethertype STRING

This command configures the ether type for the profile. Where the 
STRING is a hex-decimal value. e.g.: 08AA.

acl

no ethertype

This command removes the limitation of the ether type from the profile.

acl

source mac host 
MACADDR

This command configures the source MAC and mask for the profile.

acl

source mac MACADDR 
MACADDR

This command configures the source AMC and mask for the profile.

acl

no source mac

This command removes the source MAC and mask from the profile.

acl

source ip host IPADDR This command configures the source IP address for the profile.

acl

source ip IPADDR 
IPMASK

This command configures the source IP address and mask for the 
profile.

acl

no source ip

This command removes the source IP address from the profile.

acl

destination ip host 
IPADDR

This command configures a specific destination IP address for the 
profile.

acl

destination ip IPADDR 
IPMASK

This command configures the destination IP address and mask for the 
profile.

acl

no destination ip

This command removes the destination IP address from the profile.

acl

l4-source-port IPADDR This command configures UDP/TCP source port for the profile.

acl

no l4-source-port 
IPADDR

This command removes the UDP/TCP source port from the profile.

acl

L4-destination-port 
PORT

This command configures the UDP/TCP destination port for the profile.

acl

no l4-destination-port This command removes the UDP/TCP destination port from the profile.

acl

vlan VLANID

This command configures the VLAN for the profile.

acl

no vlan

This command removes the limitation of the VLAN from the profile.

acl

source interface  
PORT_ID

This command configures the source interface for the profile.

acl

no source interface  
PORT_ID

This command removes the source interface from the profile.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды