Comnet CWGE24MS2 Скачать руководство пользователя страница 118

Страница: 118 / 282

INS_CWGE24MS2_REV–

10/05/16 PAGE 118

INSTALLATION AND OPERATION MANUAL

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Node

Command

Description

qinq

priority <0-7>

This command sets priority in selective Q-in-Q.

qinq

access-ports PORTLISTS

This command specifies the access ports to apply the rule.

qinq

tunnel-ports PORTLISTS

This command specifies the tunnel ports to apply the rule.

qinq

end

The command exits the CLI Q-in-Q node and enters the CLI
enable node.

qinq

exit

The command exits the CLI Q-in-Q node and enter the CLI
configure node.

qinq

show

The command shows the current selective Q-in-Q profile
configurations.

configure interface range

gigabitethernet1/0/
PORTLISTS

This command enters the interface configure node.

if-range

vlan-stacking port-based
priority <0~7>

This command sets the priority in port based Q-in-Q.

if-range

vlan-stacking port-based role
(tunnel|access|normal)

This command sets VLAN stacking port role.

if-range

vlan-stacking port-based
spvid <1~4096>

This command sets the service provider’s VID of the specified
port.

if-range

vlan-stacking tunnel-tpid
index <1-6>

This command sets TPID for a Q-in-Q tunnel port.

Содержание CWGE24MS2



























































































































































































































































































Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CWGE24MS2

Отзывы:

Бренды по названию

Популярные бренды