manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 204

INS_CWGE24MS2_REV–

10/05/16     PAGE 204

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Enable the global DHCP Snooping and VLAN 1 DHCP Snooping.

 

» CWGE24MS2(config)#dhcp-snooping

 

» CWGE24MS2(config)#dhcp-snooping vlan 1

 

» CWGE24MS2(config)#interface gi1/0/1

 

» CWGE24MS2(config-if)#dhcp-snooping trust

 

» DHCP Client-1: ipconfig  /release

 

» DHCP Client-1: ipconfig  /renew

 

=> DHCP Client-1 can get an IP address.

If you configure a static host entry in the DHCP snooping binding table, and then you want to 
change the host to DHCP client, the host will not get a new IP from DHCP server, and then you 
must delete the static host entry first.

CLI Configuration

Node

Command

Description

enable

show dhcp-snooping This command displays the current DHCP snooping configurations.

configure

dhcp-snooping 
(disable|enable)

This command disables/enables the DHCP snooping on the switch.

configure

dhcp-snooping vlan 
VLANID

This command enables the DHCP snooping function on a VLAN or 
range of VLANs.

configure

no dhcp-snooping 
vlan VLANID

This command disables the DHCP snooping function on a VLAN or 
range of VLANs.

configure

dhcp-snooping server 
IPADDR

This command configures a valid DHCP server.

interface

dhcp-snooping host This command configures the maximum host count for the specific port.

interface

no dhcp-snooping 
host

This command configures the maximum host count to default for the 
specific port.

interface

dhcp-snooping trust This command configures the trust port for the specific port.

interface

no dhcp-snooping 
trust

This command configures the un-trust port for the specific port.

configure

interface range 
gigabitethernet1/0/ 
PORTLISTS

This command enters the interface configure node.

if-range

dhcp-snooping host This command configures the maximum host count for the specific ports.

if-range

no dhcp-snooping 
host

This command configures the maximum host count to default for the 
specific ports.

if-range

dhcp-snooping trust This command configures the trust port for the specific ports.

if-range

no dhcp-snooping 
trust

This command configures the un-trust port for the specific ports.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды