manualshive.com logo in svg

Comnet CWGE24MS2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comnet CWGE24MS2 Скачать руководство пользователя страница 193

INS_CWGE24MS2_REV–

10/05/16     PAGE 193

INSTALLATION AND OPERATION MANUAL 

CWGE24MS2

TECH SUPPORT: 1.888.678.9427

Parameter

Description

Instance

Selects a instance that you want to configure.

Port

Selects a port or a range of ports that you want to configure.

Path Cost

Configures the path cost for the specific port.

Priority

Configures the priority for the specific port.

Port

Selects a port or a range of ports that you want to configure.

Active

Enables/Disables the spanning tree function for the specific port.

Edge Port

Configures the port type for the specific port. Edge or Non-Edge.

BPDU Filter

Enables/Disables the BPDU filter function for the specific port.

BPDU Guard

Enables/Disables the BPDU guard function for the specific port.

ROOT Guard

Enables/Disables the BPDU root guard function for the specific port.

Port Status

Active

The state of the STP function.

Role

The port role. Should be one of the Alternated / Designated / Root / Backup / None.

Status

The port’s status. Should be one of the Discarding / Blocking / Listening / Learning / 
Forwarding / Disabled. 

Path Cost

The port’s path cost.

Priority

The port’s priority.

Edge Port

The state of the edge function.

BPDU Filter

The state of the BPDU filters function.

BPDU Guard

The state of the BPDU guards function.

ROOT Guard

The state of the BPDU Root guard function.

Содержание CWGE24MS2



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды