
(200)7A-18
OVERHAUL MANUAL
Fig. 7 A - 7 2 A - L o w and Reverse Clu tc h H o u s in g -E x p lo d e d V ie w
LO & REVER SE
CLU TC H
S E L E C T IV E
W ASHER
SNAP
R ING
(HO USING
TO CASE)
H O U S IN G
TO CASE
SPACER
LO & REVER SE
PISTON
ASSEM BLY
W AVE
RELEASE
SPRING
SNAP
R IN G
LO & REVE R S E
STEEL C L U T C H
PLATE
LO & REVER SE
C O M P O S IT IO N
FACED P LATE
LO & REVER SE
C LUTCH
HO USING
ASSEMBLY
LO & REVERSE
PISTON SEALS
LO & REVER SE
C L U T C H APPLY
R ING
LO & REVER SE
C LU TC H
SPRING
R E T A IN E R
Reassembly
1. Install clutch apply ring on low and reverse clutch
piston.
2. Install new outer and inner seals on piston with lips
facing away from clutch apply ring side.
3. Install seal protector J-25011.
N OT.fi:
Apply transmission fluid to all clutch seals
before reassembly.
CAUTION:
Flat screwdriver surface area m ust be
smooth to prevent damaging outer seal.
4. Using flat edged small screwdriver, install low and
reverse clutch piston, while rotating and pushing down into
place (Fig. 7A-77A).
5. Remove seal protector J-25011.
6. Install waved release spring (Fig. 7A-74A).
7. Install retainer, cupped faced down.
8. Compress retainer and install snap ring (Fig. 7A-
73A).
9. Check low and reverse clutch piston travel as
follows:
a. Center the low and reverse clutch housing and piston
assembly on J-25023-1 plate (Fig. 7A-78A).
b. Center steel and composition clutch plates on clutch
apply ring, then place J-25023-2 with gauge pin tow ard
housing.
c. Install spring J-25023-7 over bolt of J-25023-1.
d. Using nut and washer, compress spring J-25023-7
until washer bottom s against shoulder on J-25023-1 (Fig.
7A-78A).
SNAP RING
LO & REVERSE
CLUTCH HOUSING
WAVE RELEASE
SPRING
LO & REVERSE
CLUTCH HOUSING
Fig. 7 A - 7 3 A - R e m o v i n g or In s t a ll in g L o w and Reverse C lu tch
Fig. 7 A - 7 4 A - -R e m o v in g o r In s t a ll in g L o w and Reverse Clutch
S p r in g R e ta in in g S n a p Ring
W a v e Release S p r in g s
Содержание 1977 10 Series
