Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 88 / 149

5-9



NOTE: If the meter shows no battery voltage,

troubleshoot the battery or the main wiring har-
ness.

RESISTANCE



NOTE: Perform this test on the switch using the

following procedure.

CF274A

1. Turn the ignition switch to the ON position.

2. Set the meter selector to the OHMS position.

3. Connect either tester lead to pin C; then connect

the other tester lead to pin D.

4. The meter must show less than 1 ohm.

5. Turn the ignition switch to the LIGHTS position.

6. Connect either tester lead to pin A; then connect

the other tester lead to pin B.

7. The meter must show less than 1 ohm.

8. Connect either tester lead to pin C; then connect

the other tester lead to pin D.

9. The meter must show less than 1 ohm.

10. With the switch in the OFF position, connect the

red tester lead and the black tester lead to each of

the remaining pins. The meter must show an open

circuit on all pins.



NOTE: If the meter shows more than 1 ohm of

resistance, troubleshoot or replace the switch/
component or the connector.

Handlebar Control

Switches

The connector is the yellow one next to the steering

post. To access the connector, the steering post cover

and the right-side fender splash shield must be

removed (see Section 8).



NOTE: These tests should be made on the top

side of the connector.

RESISTANCE (HI Beam)

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to the yellow wire; then

connect the black tester lead to the gray wire.

3. With the dimmer switch in the HI position, the

meter must show less than 1 ohm.



NOTE: If the meter shows more than 1 ohm of

resistance, troubleshoot or replace the
switch/component, the connector, or the switch
wiring harness.

RESISTANCE (LO Beam)

1. Connect the red tester lead to the white wire; then

connect the black tester lead to the gray wire.

2. With the dimmer switch in the LO position, the

meter must show an open circuit.



NOTE: If the meter reads resistance, trouble-

shoot or replace the switch/component, the con-
nector, or the switch wiring harness.

DIODE (Starter Button)



NOTE: If voltage is not as specified, check the

condition of the battery in the meter prior to
replacing the switch. A low battery will result in a
low voltage reading during a diode test.

1. Set the meter selector to the Diode position.

2. Connect the red tester lead to the orange/white

wire; then connect the black tester lead to the yel-

low/green wire.

3. With the starter button depressed, the meter must

show 0.5-0.7 DC volts.

4. With the starter button released, the meter must

show 0 DC volts.

5. Connect the red tester lead to the yellow/green

wire; then connect the black tester lead to the

orange/white wire.

6. With the starter button depressed, the meter must

show 0 DC volts.



NOTE: If the meter does not show as specified,

replace the switch/component, connector, or
switch harness.

RESISTANCE (Emergency Stop)

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to the orange wire; then

connect the black tester lead to the orange/white wire.

3. With the switch in the OFF position, the meter

must show an open circuit.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды