Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 76 / 149

4-7

4. Install the front bumper and front fender panel.

5. Install the front rack.

6. Fill the cooling system with the recommended

amount of antifreeze. Check for leakage.

7. Connect the fan wiring to the main wiring harness.

THERMOSTAT

Removing



NOTE: The thermostat housing is located behind

the radiator on the left side near the top of the
radiator.

1. Drain approximately one quart of coolant from the

cooling system.

2. Remove the cap screws securing the cover to the

thermostat housing and remove the thermostat

cover and thermostat. Account for an O-ring.

Inspecting



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Inspect the thermostat for corrosion or spring damage.

2. Using the following procedure, inspect the ther-

mostat for proper operation.

A. Suspend the thermostat in a container filled with

water.

B. Heat the water and monitor the temperature

with a thermometer.

C. The thermostat should start to open at 80-84° C

(176-183° F).

D. If the thermostat does not open, it must be

replaced.

3. Inspect all coolant hoses, connections, and clamps

for deterioration, cracks, and wear.



NOTE: All coolant hoses and clamps should be

replaced every four years or 4000 miles.

Installing

Place the thermostat and O-ring into the thermostat

housing; then secure the thermostat housing cover to

the housing with the cap screws.

COOLING FAN

Removing

1. Remove the radiator (see Liquid Cooling System

in this section).

2. Remove the fan assembly from the radiator.

Installing

1. Position the fan assembly on the radiator; then

secure with existing hardware.



NOTE: The fan wiring must be in the upper-right

position.

2. Install the radiator.

WATER PUMP



NOTE: The water pump is a non-serviceable

component. It must be replaced as an assembly.

Removing

1. Remove the radiator cap; then remove the water

pump drain and drain the coolant.

FI530A

2. Drain the oil from the engine/transmission.

3. Remove four cap screws securing the water pump

cover to the water pump housing; then leaving the

hoses connected, remove the water pump cover

and lay aside.

FI530

4. Remove the six remaining cap screws securing the

water pump housing to the magneto cover; then

remove the water pump housing. Account for a

gasket and two alignment pins.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды