Arctic Cat 450 2010 Скачать руководство пользователя | Manualshive

Страница: 38 / 149

background image

3-17

3

Inspecting Cam Chain Guide

1. Inspect cam chain guide for cuts, tears, breaks, or

chips.

2. If the chain guide is damaged, it must be replaced.

Honing Cylinder

1. Using a slide gauge and a dial indicator or a snap

gauge, measure the cylinder bore diameter in three

locations from top to bottom and again from top to

bottom at 90° from the first measurements for a

total of six measurements. The trueness

(out-of-roundness) is the difference between the

highest and lowest reading. Maximum trueness

(out-of-roundness) must not exceed specifications.

CC127D

2. Wash the cylinder in parts-cleaning solvent.

3. Inspect the cylinder for pitting, scoring, scuffing,

and corrosion. If marks are found, repair the sur-

face using a #320 grit ball hone.



NOTE: To produce the proper 60° cross-hatch

pattern, use a low RPM drill (600 RPM) at the rate
of 30 strokes per minute. If honing oil is not avail-
able, use a lightweight petroleum-based oil. Thor-
oughly clean cylinder after honing using soap and
hot water. Dry with compressed air; then immedi-
ately apply oil to the cylinder bore. If the bore is
severely damaged or gouged, replace the cylinder.

CC390D

4. If any measurement exceeds the limit, bore the

cylinder and must be replaced.

Measuring Camshaft Runout



NOTE: If the camshaft is out of tolerance, it must

be replaced.

1. Place the camshaft on a set of V blocks; then posi-

tion the dial indicator contact point against the

shaft and zero the indicator.

CC283D

2. Rotate the camshaft and note runout; maximum

tolerance must not exceed specifications.

Measuring Camshaft Lobe Height

1. Using a calipers, measure each cam lobe height.

ATV1013A

2. The lobe heights must not exceed minimum speci-

fications.

Inspecting Camshaft Bearing

Journal

1. Inspect the bearing journal for scoring, seizure

marks, or pitting.

2. If excessive scoring, seizure marks, or pitting is

found, the cylinder head assembly must be

replaced.

Measuring Camshaft to
Cylinder Head Clearance

1. Loosen the jam nuts and adjuster screws.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

«
...
36
37
38
39
40
...
»

Содержание 450 2010






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 450 2010

Бренд: KAYO MOTO Страницы: 6

Бренд: Airstream Страницы: 98

Club Car Carryall 272

Бренд: Ingersoll-Rand Страницы: 44

Бренд: Xxxlutz Страницы: 58

Бренд: TOMCAR Страницы: 106

Бренд: E-Z-GO Страницы: 80

Treker 700-109P

Бренд: Land Pride Страницы: 104

Бренд: Landoll Страницы: 80

Бренд: Landoll Страницы: 82

Бренд: Parklands Страницы: 101

Бренд: MANCO Страницы: 16

Бренд: Yamaha Страницы: 108

Бренд: Baja motorsports Страницы: 11

2009 Prowler XTZ

Бренд: Arctic Cat Страницы: 169

Бренд: Arctic Cat Страницы: 174

Бренд: Metal-Fach Страницы: 42

Бренд: Tracker Off-Road Страницы: 157

Бренд: Tracker Off-Road Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды