Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 141 / 149

8-9

CD779

CD780A

8. Disconnect four headlight connectors and secure

the wires out of the way; then disconnect the wires

to the front accessory plug.

CD681

9. Rotate the handlebar to the full-left position; then

lift and slide the panel to the rear and lift the rear

up to clear the handlebar.

CD765A



NOTE: It may be necessary to rotate the body

panel to the right to align the opening with the han-
dlebar.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all fender components with warm soap and

water.

2. Inspect fenders for cracks and/or loose rivets.

3. Inspect for any missing decals.

INSTALLING

1. Rotate the handlebar to the full-left position; then

place the front body panel over the handlebar and

rotate and lower into position.

CD765

2. Connect the headlight connectors to the appropri-

ate headlights and the front accessory plug wires

to the accessory plug.

CD681

3. Make sure the rubber grommets and bushings are

in place; then place the front rack into position and

secure with the cap screws and lock nuts. Tighten

securely.

4. Install the footwells and foot rests. Tighten

securely.

5. Install the cap screws securing the front body

panel to the frame and rear panel.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды