Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 61 / 149

3-40

2. Clean the secondary driven bevel gear teeth of old

oil and grease residue.

3. Apply a thin, even coat of a machinist-layout dye

to several teeth of the gear.

4. Install the secondary driven output shaft assembly.

5. Rotate the secondary driven bevel gear several

revolutions in both directions.

6. Examine the tooth contact pattern in the dye and

compare the pattern to the illustrations.

ATV-0103

ATV-0105

ATV-0104

Correcting Tooth Contact



NOTE: If tooth contact pattern is comparable to

the correct pattern illustration, no correction is
necessary.

If tooth contact pattern is comparable to an incorrect

pattern, correct tooth contact according to the follow-

ing chart.



NOTE: To correct tooth contact, steps 1 and 2

(with NOTE) of “Correcting Backlash” must be fol-
lowed and the above “Tooth Contact/Shim Correc-
tion” chart must be consulted.

CRANKSHAFT ASSEMBLY



NOTE: The crankshaft and connecting rod is a

non-serviceable assembly. If any component is
out of specification, the assembly must be
replaced.

Measuring Connecting Rod

(Small End Inside Diameter)

1. Insert a snap gauge into the upper connecting rod

small end bore; then remove the gauge and mea-

sure it with micrometer.

CC290D

2. Maximum diameter must not exceed specifica-

tions.

Measuring Connecting Rod
(Small End Deflection)

1. Place the crankshaft on a set of V-blocks and

mount a dial indicator and base on the surface

plate. Position the indicator contact point against

the center of the connecting rod small end journal.

2. Zero the indicator and push the small end of the

connecting rod away from the dial indicator.

3. Maximum deflection must not exceed specifica-

tions.

Tooth Contact

Shim Correction

Contacts at Top

Decrease Shim Thickness

Contacts at Root

Increase Shim Thickness

CAUTION

After correcting tooth contact, backlash must again be
checked and corrected (if necessary). Continue the
correcting backlash/correcting tooth contact proce-
dures until they are both within tolerance values.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды