Arctic Cat 450 2010 страница 130 Скачать руководство пользователя

Страница: 130 / 149

7-6

AF934

8. Slide the hub out of the knuckle and set aside.

9. Remove the cap screws and lock nuts securing the

knuckle to the A-arms. Discard the lock nuts.



NOTE: Never reuse a lock nut. Once a lock nut

has been removed, it must be replaced with a new
lock nut.

10. Remove the cap screws and lock nuts securing the

A-arms to the frame; then remove the A-arms.



NOTE: If removing the upper right A-arm, it will

be necessary to disconnect the brake hose from
the A-arm.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all A-arm components using a pressure

washer.

2. Inspect the A-arm for bends, cracks, and worn

bushings.

3. Inspect the frame mounts for signs of damage,

wear, or weldment damage.

INSTALLING

1. Install the A-arm assemblies into the frame

mounts and secure with the cap screws and new

lock nuts. Only finger-tighten at this time.

2. Slide the knuckle onto the drive axle and into posi-

tion on the A-arms; then secure the knuckle to the

A-arms with cap screws and new lock nuts.

Tighten to 50 ft-lb.

3. Tighten the hardware securing the A-arms to the

frame mounts (from step 1) to 50 ft-lb.

4. Apply grease on the drive axle splines; then install

the hub assembly onto the drive axle.

PR290

5. Secure the hub assembly with the nut. Tighten

only until snug.

6. Secure the brake caliper to the knuckle with two

new “patch-lock” cap screws (right side only).

Tighten the caliper to 20 ft-lb.



NOTE: Ensure that the brake hose is properly

routed and secured to the upper A-arm.

DE054A

7. Compress the hand brake lever and engage the

brake lever lock; then secure the hub nut (from

step 5) to the drive axle. Tighten to 200 ft-lb.

8. Install a new cotter pin and spread the pin to

secure the nut.



NOTE: If the cotter pin does not line up, always

tighten to the next alignment.

PR260

9. Secure the shock absorber to the frame with a cap

screw and new lock nut. Tighten to 50 ft-lb.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды