Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 78 / 149

4-9

INSPECTING

1. Inspect the fuel screen and blow clean with low

pressure compressed air.

2. Move the float lever and check for free movement.

The float assembly should return to the lower posi-

tion without force. If not, replace the fuel pump

assembly.

3. Test the fuel level sensor by connecting a multime-

ter (A) to the fuel level sensor leads (B); then

select OHMS. The multimeter should show 5

ohms at full fuel position (C) and 95 ohms at

empty fuel position (D).

ATV2116



NOTE: If readings are erratic, clean the resistor

wiper and resistor with clean alcohol and retest. If
still not correct, replace the fuel level sensor.

4. To replace the fuel level sensor, use the following

procedure.

A. Disconnect the two-wire connector (A); then

press the fuel level sensor toward the top of the

fuel pump to release it from the mounting slot

(B).

FI460A

B. Engage the tabs (C) of the fuel level sensor into

the mounting slot (B) and press toward the bot-

tom of the fuel pump to latch in place; then con-

nect the two-wire connector (A).

INSTALLING

1. Mark the new fuel pump with a reference mark in

the same location as the removed pump; then place

the new gasket on the pump.

2. Remove the material covering the fuel pump open-

ing; then carefully guide the fuel pump into posi-

tion taking care not to damage the float or float

lever.

KX190

3. Rotate the fuel pump until the match marks align;

then install the mounting screws and tighten

securely using a crisscross pattern.



NOTE: It is important to install the fuel pump with

the correct orientation to ensure adequate float
lever clearance.

4. Connect the wires, fuel hose, and spring clamp;

then turn the ignition switch to the ON position.

Note that the fuel pump runs momentarily and the

fuel gauge indicates the proper fuel level.

5. With the transmission in neutral and brake lever

lock engaged, start the engine and check for nor-

mal operation. Check for any fuel leaks.

6. Install any wire ties that were removed; then

install the rear fenders, rack, and seat making sure

the seat locks securely.



AT THIS POINT

If the pump has failed earlier test and must be
replaced, proceed to INSTALLING.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды