manualshive.com logo in svg

Arctic Cat 450 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat 450 2010 Скачать руководство пользователя страница 12

2-5

2

CF005

2. Rotate the crankshaft to the TDC position on the

compression stroke.

NOTE: At this point, the rocker arms and adjuster

screws must not have pressure on them.

NOTE: Use Valve Clearance Adjuster for this pro-

cedure.

3. Place the valve adjuster onto the jam nut securing

the tappet adjuster screw; then rotate the valve

adjuster dial clockwise until the end is seated in

the tappet adjuster screw.

4. While holding the valve adjuster dial in place, use

the valve adjuster handle and loosen the jam nut;

then rotate the tappet adjuster screw clockwise

until friction is felt.

5. Align the valve adjuster handle with one of the

marks on the valve adjuster dial.

6. While holding the valve adjuster handle in place,

rotate the valve adjuster dial counterclockwise

until proper valve/tappet clearance is attained.

NOTE: Refer to the appropriate specifications in

Feeler Gauge Procedure sub-section for the
proper valve/tappet clearance.

NOTE: Rotating the valve adjuster dial counter-

clockwise will open the valve/tappet clearance by
0.05 mm (0.002 in.) per mark.

7. While holding the adjuster dial at the proper clear-

ance setting, tighten the jam nut securely with the

valve adjuster handle.

8. Place the two tappet covers with O-rings into posi-

tion; then tighten the covers securely.

9. Install the spark plug; then install the timing

inspection plug.

Testing Engine 

Compression

To test engine compression, use the following proce-

dure.

1. Remove the high tension lead from the spark plug.

2. Using compressed air, blow any debris from

around the spark plug.

3. Remove the spark plug; then attach the high ten-

sion lead to the plug and ground the plug on the

cylinder head well away from the spark plug hole.

4. Attach the Compression Tester Kit.

NOTE: The engine should be warm (operating

temperature) and the battery full charged for an
accurate compression test.  Throttle must be in the
wide-open throttle (WOT) position.

5. While holding the throttle lever in the full-open

position, crank the engine over with the electric

starter until the gauge shows a peak reading (five

to 10 compression strokes). Compression should

be 95-115 psi.

6. If compression is abnormally low, inspect the

following items.

A. Verify starter cranks engine over at normal

speed (approximately 400 RPM).

B. Gauge functioning properly.

C. Throttle lever in the full-open position.

D. Valve/tappet clearance correct.

E. Valve not bent or burned.

F. Valve seat not burned.

NOTE: To service valves, see Section 3.

7. Pour 29.5 ml (1 fl oz) of oil into the spark plug

hole, reattach the gauge, and retest compression.

8. If compression is now evident, service the piston

rings (see Section 3).

! WARNING

Always wear safety glasses when using compressed
air.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды