Arctic Cat 450 2010 страница 64 Скачать руководство пользователя

Страница: 64 / 149

3-43

FI671

ASSEMBLING

1. With the high driven washer (1) on the counter-

shaft, install the high driven gear bushing (3),

bearings (2), and gear (4) on the countershaft; then

install the washers (5) and secure with the

snap-ring.

FI671A

FI670

2. Install the high/low shift dog (6) on the counter-

shaft and secure with snap-ring (7); then install the

splined washer (8).

FI668A

3. Install the low driven bushing (10), bearing (9)

and gear (11) on the countershaft; then install

splined washer (12).

FI667A

FI666

4. Place the reverse driven bushing (13) onto the

shaft; then install the bearing (14), gear (15) and

splined washer (16). Secure with a snap-ring.

FI665A

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды