manualshive.com logo in svg

Arctic Cat 450 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat 450 2010 Скачать руководство пользователя страница 32

3-11

3

11. Remove the two nuts securing the right side of the

cylinder to the right-side crankcase half.

FI622A

12. Lift the cylinder off the crankcase taking care not

to allow the piston to drop against the crankcase.

Account for the gasket and two alignment pins.

FI624A

13. Using an awl, remove one piston-pin circlip. Take

care not to drop it into the crankcase.

FI625

14. Using Piston Pin Puller, remove the piston pin.

Account for the opposite-side circlip. Remove the

piston.

NOTE: It is advisable to remove the opposite-side

circlip prior to using the puller.

MD1219

NOTE: Support the connecting rod with rubber

bands to avoid damaging the rod or install a con-
necting rod holder.

Servicing Top-Side 

Components

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

VALVE ASSEMBLY

When servicing valve assembly, inspect valve seats,

valve stems, valve faces, and valve stem ends for pits,

burn marks, or other signs of abnormal wear.

NOTE: Whenever a valve is out of tolerance, it

must be replaced.

Cleaning/Inspecting Cylinder Head 

Cover

NOTE: If the cylinder head cover cannot be trued,

the cylinder head assembly must be replaced.

1. Wash the cylinder head cover in parts-cleaning

solvent.



AT THIS POINT

To service cylinder, see Servicing Top-Side Compo-
nents sub-section.

CAUTION

When removing the cylinder, be sure to support the
piston to prevent damage to the crankcase and piston.

CAUTION

Do not allow the connecting rod to go down inside the
crankcase. If the rod is down inside the crankcase and
the crankshaft is rotated, severe damage will result.



AT THIS POINT

To service piston, see Servicing Top-Side Compo-
nents sub-section.



AT THIS POINT

To service center crankcase components only, pro-
ceed to Removing Left-Side Components.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды