Arctic Cat 450 2010 страница 84 Скачать руководство пользователя

Страница: 84 / 149

5-5

FI489

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage,

troubleshoot the battery, fuse, or the main wiring
harness.



NOTE: If the meter shows battery voltage, the

main wiring harness is good; proceed to test the
switch/component, the connector, and the switch
wiring harness for resistance.

RESISTANCE (Switch Connector)



NOTE: The brake lever must be compressed for

this test.

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to one black wire; then

connect the black tester lead to the brown wire.

FI490

3. When the lever is compressed, the meter must

show less than 1 ohm.



NOTE: If the meter shows more than 1 ohm of

resistance, replace the switch.

Engine Coolant

Temperature (ECT)

Sensor

1. Connect the meter leads (selector in OHMS posi-

tion) to the sensor terminals.

2. Suspend the sensor and a thermometer in a con-

tainer of cooking oil; then heat the oil.



NOTE: Neither the sensor nor the thermometer

should be allowed to touch the bottom of the con-
tainer or inaccurate readings will occur. Use wire
holders to suspend the sensor and thermometer.

3. On the ECT sensor when the temperature reaches

60° C (140° F), the meter should read approxi-

mately 700 ± 40 ohms.

4. On the ECT sensor when the temperature reaches

90° C (194° F), the meter should read approxi-

mately 200 ± 15 ohms.

5. On the ECT sensor when the temperature reaches

120° C (248° F), the meter should read approxi-

mately 111 ± 7 ohms.

6. If the readings are not as indicated, the sensor

must be replaced.

7. Install the sensor and tighten securely.

8. Connect the leads.

Fan Motor

The connector is the black two-prong one located

above the oil cooler/radiator.



NOTE: The ignition switch must be in the ON

position.

RESISTANCE

(Fan Motor Connector)

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to the red wire; then

connect the black tester lead to the black wire.

! WARNING

Wear insulated gloves and safety glasses. Heated oil
can cause severe burns.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды