Arctic Cat 450 2010 страница 114 Скачать руководство пользователя

Страница: 114 / 149

6-16

AF897D

8. Secure the tie rods with the lock nuts. Tighten to

30 ft-lb; then install and spread the cotter pins.

AF896D

AF895D

9. Install the brake calipers and secure with new

“patch-lock” cap screws tightened to 20 ft-lb.

AF894D

10. Install the wheels and tighten to 40 ft-lb.

11. Remove the ATV from the support stand.

Drive Axles

REMOVING REAR DRIVE AXLE

1. Secure the ATV on a support stand to elevate the

wheels.

2. Pump up the hand brake; then engage the brake

lever lock.

3. Remove the wheel.

4. Remove the cotter pin securing the hex nut; then

remove the hex nut. Release the brake lever lock.

KX041

5. Remove the two brake calipers (right side only).



NOTE: Do not allow the brake calipers to hang

from their cable/hose.

6. Slide the hub out of the knuckle and set aside.

7. Remove the cap screw and lock nut securing the

knuckle to the upper A-arm. Discard the lock nut.



NOTE: Never reuse a lock nut. Once a lock nut

has been removed, it must be replaced with a new
lock nut.

8. While holding the drive axle stationary, pull the

top of the knuckle out and down until it is free of

the drive axle.

9. Place a drain pan under the ATV to contain any oil

leakage; then using a slide hammer, remove the

drive axle.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

CAUTION

The calipers should be supported. If the calipers are
allowed to hang from the cable/hose, damage may
occur.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды