Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 46 / 149

3-25

Servicing Left-Side

Components

INSPECTING STARTER
CLUTCH/GEAR

1. Place the starter clutch gear onto the rotor/fly-

wheel and attempt to rotate the starter clutch gear

clockwise. It should lock up to the rotor/flywheel.

Rotate the gear counterclockwise and it should

turn freely. If it moves or locks up both ways, the

starter clutch must be replaced.

2. Inspect the starter clutch gear for chipped or miss-

ing teeth or discoloration/scoring of the clutch sur-

face. Inspect the bearing for loose, worn, or

discolored rollers. If bearing is damaged, it must

be replaced.

FI569

3. Inspect the one-way bearing for chipped surfaces,

missing rollers, or discoloration. If any of the

above conditions exist, replace the starter clutch

assembly.

FI572

REPLACING STARTER CLUTCH

ASSEMBLY

1. Remove the cap screws securing the one-way

clutch assembly to the flywheel; then remove from

the flywheel.

FI570

2. Thoroughly clean the rotor/flywheel; then install

the new one-way clutch and secure with the cap

screws after applying a drop of red Loctite #271 to

the threads. Tighten to 26 ft-lb using a crisscross

pattern. Make sure the one-way bearing is installed

with the notches directed away from the rotor/fly-

wheel.

FI576A

FI578

REPLACING STARTER GEAR
BEARING

1. Support the starter clutch gear in a press making

sure to support the hub around the entire circum-

ference; then using a suitable bearing driver, press

the bearing from the gear.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды