Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 28 / 149

3-7

FI519A

8. Disconnect the crankcase breather hose from the

air filter housing and remove the air filter assem-

bly.

9. From the top side, remove the engine coolant tem-

perature (ECT) sensor connector (C), fuel injector

connector (D), manifold absolute pressure (MAP)

sensor connector (E), idle step control (ISC) con-

nector (F), and throttle position sensor (TPS) con-

nector (G).

FI522A

10. From the right side, disconnect the stator connec-

tor (H) and crankshaft position sensor connector

(I) from the main harness; then disconnect the pos-

itive cable from the starter motor and the engine

ground cable from the starter mounting flange.

FI523A

FI533A

11. Remove the screens securing throttle arm cover to

the throttle body; then loosen the throttle cable

jam-nut and remove the throttle cable.

FI536A

12. Remove the cap screws securing the exhaust pipe

to the cylinder head; then remove the springs

securing the muffler to the exhaust pipe.

13. Remove the muffler and exhaust pipe. Account for

a grafoil seal on each end of the exhaust pipe.

14. Remove coolant hoses (A) and (B) from the water

pump; then remove the upper coolant hose from

the thermostat housing.

FI530B

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды