Arctic Cat 450 2010 страница 119 Скачать руководство пользователя

Страница: 119 / 149

6-21

Rear Gear Case

REMOVING

1. Remove the left-side rear A-arms (see Rear

A-Arms in Section 7).

2. Remove both of the rear drive axles (see Drive

Axles in this section).

3. Remove the four cap screws securing the engine

output shaft to the rear gear case input flange.

CD028

4. Remove the two cap screws and lock nuts securing

the rear gear case to the frame; then remove the

gear case through the left side.

AF960A

Hub

REMOVING

1. Secure the ATV on a support stand to elevate the

wheel; then remove the wheel.

2. Remove the cotter pin from the nut.



NOTE: During assembly, new cotter pins should

be installed.

KX041

3. Remove the flange nut securing the hub.

4. Remove the brake caliper.

PR243A

5. Remove the hub assembly.

6. Remove the four cap screws securing the brake

disc.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all hub components.

2. Inspect all threads for stripping or damage.

3. Inspect the brake disc for cracks or warping.

4. Inspect the hub for pits, cracks, loose studs, or

spline wear.



AT THIS POINT

For servicing the input shaft, pinion gear, needle
bearing, and axle seal, see Front Differential in this
section.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды