Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 73 / 149

4-4

FI528A

6. Install the storage compartment, storage compart-

ment cover, and seat making sure the seat locks

securely.

Fuel Injector

REPLACING

1. Turn the ignition switch to the OFF position and

remove the key; then disconnect the negative bat-

tery cable from the battery.

2. Remove the air filter housing assembly (see Throt-

tle Body - REMOVING - steps 1-6 in this section).

3. Remove the gasline connector from the fuel rail.

FI527A

4. Remove the fuel injector electrical connector; then

remove the two cap screws securing the fuel infec-

tor to the intake pipe.

FI528B

5. Remove the fuel injector from the intake pipe.

6. Place the new fuel injector into the intake pipe;

then secure with two cap screws. Tighten to 8

ft-lb.

7. Connect the harness connector to the fuel injector;

then connect the gasline hose.

8. Install the air filter housing assembly (see Throttle

Body - INSTALLING - steps 4-7 in this section).

9. Connect the negative battery cable to the battery.

Throttle Cable Free-Play

To adjust the throttle cable free-play, follow this proce-

dure.

1. Slide the rubber boot away; then loosen the jam

nut from the throttle cable adjuster.

AL611D

2. Turn the adjuster until the throttle cable has proper

free-play of 3-6 mm (1/8-1/4 in.) at the lever.

! WARNING

Always disable the electrical system when the gasline
hoses will be disconnected. Inadvertent activation of
the electric fuel pump will force gasoline from the
gasline hose causing a fire or explosion hazard.

! WARNING

Gasoline may be under pressure. Place an absorbent
towel under the connector to absorb any gasoline
leakage when disconnecting.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды