manualshive.com logo in svg

Arctic Cat 450 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat 450 2010 Скачать руководство пользователя страница 18

2-11

2

Hydraulic Brake 

Systems

CHECKING/BLEEDING

The hydraulic brake systems have been filled and bled

at the factory. To check and/or bleed a hydraulic brake

system, use the following procedure.

1. With the master cylinder in a level position, check

the fluid level in the reservoir. On the hand brake

if the level in the reservoir is adequate, the sight

glass will appear dark. If the level is low, the sight

glass will appear clear. On the auxiliary brake, the

level must be between the MIN and MAX lines on

the reservoir.

738-420A

AL681

2. Compress the brake lever/pedal several times to

check for a firm brake. If the brake is not firm, the

system must be bled.

3. To bleed the main brake system, use the following

procedure.

A. Remove the cover and fill the reservoir with

DOT 4 Brake Fluid.

B. Install and secure the cover; then slowly com-

press the brake lever several times.

C. Remove the protective cap, install one end of a

clear hose onto one FRONT bleeder screw, and

direct the other end into a container; then while

holding slight pressure on the brake lever, open

the bleeder screw and watch for air bubbles.

Close the bleeder screw before releasing the

brake lever. Repeat this procedure until no air

bubbles are present.

AF637D

PR377C

NOTE: During the bleeding procedure, watch the

reservoir/sight glass very closely to make sure
there is always a sufficient amount of brake fluid. If
low, refill the reservoir before the bleeding proce-
dure is continued. Failure to maintain a sufficient
amount of fluid in the reservoir will result in air in
the system.

D. At this point, perform step B and C on the other

FRONT bleeder screw; then move to the REAR

bleeder screw and follow the same procedure.

E. Repeat step D until the brake lever is firm.

4. To bleed the auxiliary brake system, use the fol-

lowing procedure.

A. Remove the cover and fill the reservoir with

DOT 4 Brake Fluid.

B. Install and secure the cover; then slowly com-

press the brake pedal several times.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды