Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 20 / 149

2-13

PR377B

E. Install the wheel. Tighten to 40 ft-lb.

5. Burnish the brake pads (see Burnishing Brake

Pads in this section).

Burnishing Brake Pads

Brake pads (both hydraulic and auxiliary) must be bur-

nished to achieve full braking effectiveness. Braking

distance will be extended until brake pads are properly

burnished. To properly burnish the brake pads, use the

following procedure.

1. Choose an area large enough to safely accelerate

the ATV to 30 mph and to brake to a stop.

2. Accelerate to 30 mph; then compress brake lever

or apply the auxiliary brake to decelerate to 0-5

mph.

3. Repeat procedure on each brake system five times.

4. Adjust the auxiliary brake (if necessary).

5. Verify that the brakelight illuminates when the

hand lever is compressed or the brake pedal is

depressed.

Checking/Replacing

V-Belt

REMOVING

1. Remove the right-side footrest (see Section 8).

2. Remove the cap screws securing the V-belt cover

noting the location of the different-lengthed cap

screws for installing purposes; then using a rubber

mallet, gently tap on the cover tabs to loosen the

cover. Remove the cover.

CD078



NOTE: Note the location of the main engine

ground wire for installing purposes.

3. Remove the nut securing the movable drive face;

then remove the face. Account for the flat washer

and spacer.



NOTE: Keep the drive face plate in contact with

the drive face when removing or installing the
drive face to prevent the rollers from falling out.

CD963

CD966A

4. Install one of the CVT cover cap screws into the

driven pulley fixed face; then turn the cap screw

clockwise to spread the pulley faces. Remove the

V-belt.

! WARNING

Failure to properly burnish the brake pads could lead
to premature brake pad wear or brake loss. Brake loss
can result in severe injury.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды