Arctic Cat 450 2010 страница 51 Скачать руководство пользователя

Страница: 51 / 149

3-30

MD1036

. Using a 6 mm cap screw threaded into the fixed

driven face, spread the driven pulley by turning the
cap screw clockwise; then remove the V-belt.

KC132

6. Remove the fixed drive face.

MD1094

Remove the nut holding the driven pulley assem-
bly; then remove the driven pulley assembly.

MD1068

8. Using an impact screwdriver, remove the three

Phillips-head cap screws holding the air intake

plate. Remove the air intake plate.

MD1092

9. Remove the cap screws holding the clutch cover

onto the right-side crankcase half. Note the posi-

tions of the different-lengthed cap screws for

installing purposes

10. Using a rubber mallet, loosen

the clutch cover;

then pull it away from the right-side crankcase

half. Account for two alignment pins and gasket.

MD1115

D. Centrifugal Clutch Assembly
E. Oil Pump Drive Gear
F. Oil Pump Driven Gear



NOTE: Steps 1-10 in the preceding sub-section

must precede this procedure.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды