Arctic Cat 450 2010 страница 147 Скачать руководство пользователя

Страница: 147 / 149

9-2

Hand Brake Lever/

Master Cylinder

Assembly



NOTE: The master cylinder is a non-serviceable

component; it must be replaced as an assembly.

REMOVING

1. Slide a piece of flexible tubing over one of the

wheel bleeder valves and direct the other end into

a container. Remove the reservoir cover; then open

the bleeder valve. Allow the brake fluid to drain

completely.



NOTE: Compressing the brake lever several

times will quicken the draining process.

AF637D

2. Place an absorbent towel around the connection to

absorb brake fluid. Remove the banjo-fitting from

the master cylinder. Account for two crush wash-

ers and a banjo-fitting bolt.

DE059A

3. Remove the snap ring and pivot pin securing the

brake lever to the master cylinder housing; then

remove the brake lever and set aside.

4. Dislodge the brakelight switch from the master

cylinder housing by gently pressing it toward the

pivot pin hole in the housing; then lay it aside

leaving the switch and wiring harness connected.

BC205

5. Remove the clamp screws securing the brake

housing to the handlebar; then remove the assem-

bly from the handlebar.

DE058A

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Inspect the pin securing the brake lever for wear.

2. Inspect the brake lever for elongation of the pivot

hole.

3. Inspect the reservoir for cracks and leakage.

4. Inspect the banjo-fitting for cracks and deteriora-

tion and the condition of the fittings (threaded and

compression).

5. Inspect the brakelight switch for corrosion, cracks,

missing or broken mounting tabs, or broken and

frayed wiring.



NOTE: If the brakelight switch is determined to

be not serviceable, see Section 5.

CAUTION

Brake fluid is highly corrosive. Do not spill brake fluid
on any surface of the ATV.

Next

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды