Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 44 / 149

3-23

FI538

2. Remove the water pump housing assembly noting

the location of the longer cap screw. Account for a

gasket and two alignment pins.

FI539

FI541

3. Remove two cap screws and the oil bolt securing

the oil pressure relief line to the engine. Account

for two crush washers and an O-ring.

FI544

4. Remove the water pump drive gear; then remove

the speed sensor housing assembly. Account for

two alignment pins, a gasket, and two seal wash-

ers.

FI543

5. Remove the cap screws securing the magneto

cover to the crankcase. Note the location of the two

internal cap screws and the two longer cap screws.

FI596A

6. Remove the magneto cover and account for two

alignment pins and the gasket.

D. Rotor/Flywheel
E. Starter Clutch/Gear

F. Starter Motor



NOTE: Steps 1-6 in the preceding sub-section

must precede this procedure.

7. Remove the nut securing the rotor/flywheel on the

crankshaft and install the crankshaft protector.

FI549

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды