Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 140 / 149

8-8

733-559A

Front Rack

REMOVING

1. Remove the cap screws and lock nuts securing the

rack to the frame and front fender panel.

2. Remove the front rack from the ATV.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all rack components using a pressure

washer.

2. Inspect all welds for cracking or bending.

3. Inspect threaded areas of all mounting bosses for

stripping.

4. Inspect for missing decals and/or reflectors.

INSTALLING

1. Place the rack into position on the frame and front

fender panel. Install the cap screws and lock nuts

and finger-tighten only.

2. Install the two cap screws and lock nuts securing

the rack to the fenders. Tighten all hardware

securely.

Front Bumper Assembly

REMOVING

1. Remove the two flange bolts and lock nuts secur-

ing the upper bumper supports to the bumper.

2. Remove the through-bolt and lock nut securing the

bumper to the frame; then remove the bumper.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all bumper components with parts-cleaning

solvent.

2. Inspect all welds for cracking or bending.

INSTALLING

1. Place the front bumper assembly into position and

install the through-bolt. Start the lock nut and fin-

ger-tighten only.

2. Install the two flange bolts and lock nuts on the

upper supports. Tighten all hardware securely.

Front Body Panel/

Side Panels

REMOVING

1. Remove the cap screws securing the radiator

access cover and remove the cover; then remove

two reinstallable rivets securing the steering post

cover and remove the cover.

2. Unlock the storage compartment lid; then slide the

storage compartment cover assembly forward and

lift off the storage compartment.

3. Remove the storage compartment box; then

remove the seat.

4. Remove the ignition switch retaining ring and two

reinstallable rivets securing the instrument pod;

then remove the instrument pod.

5. Remove the cap screws and lock nuts securing the

front rack to the frame; then remove the front rack.

Account for the grommets and bushings.

6. Remove the side panels by pulling on them to

release the tabs from the body; then remove the

screws securing the rear of the front panel to the

frame.

7. Remove the left and right footwells; then remove

the shift knob. Remove the shift lever pivot axle

nut and remove the axle and shift lever. Account

for a spring and two O-rings.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды