Arctic Cat 450 2010 Скачать руководство пользователя | Manualshive

Страница: 131 / 149

background image

7-7

7

10. Secure the shock absorber to the lower A-arm with

a cap screw and new lock nut. Tighten to 20 ft-lb.

11. Secure the boot guard to the lower A-arm with the

two cap screws. Tighten securely.

12. Install the wheel and tighten to 40 ft-lb.

13. Remove the ATV from the support stand.

Wheels and Tires

0741-559

TIRE SIZE

The ATV is equipped with low-pressure tubeless tires

of the size and type listed in Section 1. Do not under

any circumstances substitute tires of a different type or

size.

TIRE INFLATION PRESSURE

Front and rear tire inflation pressure should be 0.35

kg/cm² (5.0 psi).

REMOVING

1. Secure the ATV on a support stand to elevate the

wheels.

2. Remove the wheels.



NOTE: Keep left-side and right-side wheels sepa-

rated for installing them on their proper sides.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean the wheels and hubs using a pressure

washer.

2. Inspect each wheel for cracks, dents, or bends.

3. Inspect each tire for cuts, wear, missing lugs, and

leaks.

INSTALLING

Install each wheel on its hub. Tighten to 40 ft-lb.



NOTE: Make sure each wheel is installed on its

proper hub as noted in removing (the “rotation
arrow” if applicable must indicate forward direc-
tion of rotation).

AF612D

CHECKING/INFLATING

1. Using an air pressure gauge, measure the air pres-

sure in each tire. Adjust the air pressure as neces-

sary to meet the recommended inflation pressure.

2. Inspect the tires for damage, wear, or punctures.



NOTE: Be sure all tires are the specified size and

have identical tread pattern.



NOTE: If pulling is noted, measure the circumfer-

ence of the front and rear tires on the pulling side.
Compare the measurements with the tires on the
opposite side. If pulling is noted during braking
only, check and adjust the brakes as necessary
and recheck operation (see Section 2).

! WARNING

Use only Arctic Cat approved tires when replacing
tires. Failure to do so could result in unstable ATV
operation.

! WARNING

Do not mix tire tread patterns. Use the same pattern
type on front and rear. Failure to heed warning could
cause poor handling qualities of the ATV and could
cause excessive drive train damage not covered by
warranty.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

KEY

1. Shoulder Screw

2. Brake Disc

3. Wheel Hub - Front

4. Hub Stud

5. Wheel Hub - Rear

6. Hex Nut

7. Cotter Pin

8. Wheel

9. Mounting Nut

10. Tire

11. Valve Stem

12. Valve Stem Cap

! WARNING

Do not operate the ATV if tire damage exists.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

«
...
129
130
131
132
133
...
»

Содержание 450 2010






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 450 2010

Бренд: Yutrax Страницы: 10

Бренд: Team Durango Страницы: 32

Бренд: MANCO Страницы: 5

FourTrax Rancher TRX420FE1 2020

Бренд: Honda Страницы: 273

Бренд: Panther Страницы: 10

Бренд: Can-Am Страницы: 152

2011 commander 1000

Бренд: Can-Am Страницы: 423

Бренд: Iron Baltic Страницы: 24

Бренд: Kinroad Страницы: 80

Бренд: NorAM Страницы: 118

Бренд: PRONAR Страницы: 116

2009 Ranger RZR 800 EFI

Бренд: Polaris Страницы: 332

jay 2016 series

Бренд: Jayco Страницы: 157

Бренд: Baja motorsports Страницы: 44

Бренд: Jayco Страницы: 93

Бренд: FEISHEN Страницы: 116

POWERSPORTS FR5DGK

Бренд: MotoTec Страницы: 32

Бренд: Wallenstein Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды