manualshive.com logo in svg

Arctic Cat 450 2010, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat 450 2010 Скачать руководство пользователя страница 142

8-10

6. Install the shift lever spring, shift lever, and pivot

axle; then tighten the axle nut securely.

CD779

7. Install the instrument pod and ignition switch; then

secure with two reinstallable rivets and the igni-

tion switch retaining ring.

8. Set the storage compartment box into position;

then install the storage compartment cover making

sure the mounting tabs engage the slots. Slide rear-

ward to secure and lock by engaging the lid lock.

9. Install the steering post cover and secure with the

cap screws; then install and secure the radiator

access panel.

10. Install the side panels.

Footrests

REMOVING

1. Remove the machine screws and flange nuts

securing the front and rear fenders to the footwells.

2. Remove the screws securing the foot pegs to the

footrests; then remove the foot pegs and footwells.

3. Remove the cap screws and flange nuts securing

the footrests to the frame; then remove the foot-

rests.

CLEANING AND INSPECTING

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean the footrest in parts-cleaning solvent.

2. Inspect the footrest weldments for cracks or

unusual bends.

3. Inspect all tubing for cracks or unusual bends.

INSTALLING

1. Secure the footrests to the frame with four cap screws

and two flange nuts; then tighten the 8 mm hardware

to 20 ft-lb and the 10 mm hardware to 40 ft-lb.

2. Place the footwells onto the footrests; then put the

foot pegs in position and secure with two cap

screws.

3. Install the machine screws and flange nuts secur-

ing the front and rear fenders to the footwells.

Belly Panel

REMOVING/INSTALLING

1. Remove the machine screws and shoulder washers

securing the belly panel to the underside of the

frame; then remove the belly panel.

2. Place the belly panel into position on the underside

of the frame; then install the machine screws and

shoulder washers. Tighten securely.

Exhaust System

REMOVING MUFFLER

1. Remove the two exhaust springs at the muf-

fler/exhaust pipe juncture.

CF138A

2. Slide the muffler rearward to clear the mounting

lugs and remove the muffler.

INSPECTING MUFFLER

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Inspect muffler externally for cracks, holes, and

dents.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды