Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 65 / 149

3-44

FI664

5. Install the reverse dog on the shaft; then place the

shift forks and shift shaft into position.

FI663

FI662



NOTE: The countershaft assembly is now ready

to be installed.

Assembling Crankcase

Half



NOTE: For ease of assembly, install components

on the right-side crankcase half.



NOTE: If the output shaft was removed, make

sure that the proper shim is installed.

1. Install the output shaft into the crankcase making

sure the two gears, shim, washer, and nut are in the

correct order.

MD1199

MD1079

2. Install and tighten the output shaft flange nut to 59

ft-lb. Using a punch, peen the nut.

MD1333

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды