Arctic Cat 450 2010 Скачать руководство пользователя

Страница: 34 / 149

3-13

Measuring Valve Face/Seat Width

1. Using a calipers, measure the width of the valve

face.

FI367

2. Acceptable width must be at or above specifica-

tions.

Measuring Valve Face Radial
Runout

1. Mount a dial indicator on the surface plate; then

place the valve stem on a set of V blocks.

2. Position the dial indicator contact point on the out-

side edge of the valve face; then zero the indicator.

ATV1082A

3. Rotate the valve in the V blocks.

4. Maximum runout must not exceed specifications.

Measuring Valve Guide
(Inside Diameter)

1. Insert a snap gauge 1/2 way down into each valve

guide bore; then remove the gauge and measure it

with a micrometer.

2. Acceptable inside diameter range must be within

specifications.

3. If a valve guide is out of tolerance, the cylinder

head must be replaced.

Servicing Valves/Valve
Guides/Valve Seats

If valves, valve guides, or valve seats require servicing

or replacement, Arctic Cat recommends that the com-

ponents be taken to a qualified machine shop for ser-

vicing.

Measuring Rocker Arm
(Inside Diameter)

1. Using a dial calipers, measure the inside diameter

of the rocker arm.

2. Acceptable inside diameter range must be within

specifications.

Measuring Rocker Arm Shaft
(Outside Diameter)

1. Using a micrometer, measure the outside diameter

of the rocker arm shaft.

2. Acceptable outside diameter range must be within

specifications.

Installing Valves

1. Apply grease to the inside surface of the valve

seals; then place a lower spring seat and valve

guide seal over each valve guide.

CC144D

2. Insert each valve into its original valve location.

3. Install the valve springs with the painted end of the

spring facing away from the cylinder head.



NOTE: If the paint is not visible, install the ends

of the springs with the closest wound coils toward
the head.

CAUTION

If valves are discolored or pitted or if the seating sur-
face is worn, the valve must be replaced. Do not
attempt to grind the valves or severe engine damage
may occur.

Next

Back

Section

Table of Contents

Manual

Table of Contents

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Содержание 450 2010






















































































































































Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды

Arctic Cat 450 2010, Руководство по обслуживанию

Результаты поиска

Содержание 450 2010

Отзывы:

Похожие инструкции для 450 2010

Бренды по названию

Популярные бренды